3.7V 6800mAh 18650 Lithium Battery

3.7V 6800mAh 18650 Lithium Battery

SKU: SPKBAT001  · Category: Batteries

RWF 5,000

In stock

This is a rechargeable 18650 lithium-ion cell, rated at 3.7 V and 6800 mAh. The 18650 is one of the most widely used cell formats, found in power banks, torches, laptop packs, e-bikes and DIY battery projects, so it fits a huge range of holders, chargers and battery shields.

Because it is a lithium-ion cell, it delivers steady voltage while it discharges and can be recharged hundreds of times. It is compact, lightweight and built for demanding use. It is sold mainly for airsoft equipment, and buyers also use it in torches and portable electronics.


Use it as a single cell for 3.7 V projects, or build packs in series (more voltage) or parallel (more capacity) with matched cells and a proper battery management system (BMS).


Features

  • Rated capacity of 6800 mAh (manufacturer figure) for long run times
  • Nominal voltage of 3.7 V, the standard for single-cell Li-ion
  • Standard 18650 format that fits common holders and chargers
  • Rechargeable lithium-ion chemistry with stable discharge
  • Compact and lightweight


Specifications

  • Type: rechargeable lithium-ion (Li-ion) cell
  • Rated capacity: 6800 mAh (manufacturer figure)
  • Size: 18650 (about 18 mm diameter ร— 65 mm length)
  • Rated energy:** about 25 Wh (3.7 V ร— 6.8 Ah)
  • Typical use: airsoft AEGs, torches and other 18650-compatible devices


!!! What the capacity means in practice: Run time is roughly capacity รท load current, before converter losses.

 Load curren x Approx. run time

 100 mA โ‰ˆ 68 h

 500 mA โ‰ˆ 13.6 h

 1 A โ‰ˆ 6.8 h

 2 A โ‰ˆ 3.4 h


 Battery structure description

    * Positive (+) terminal: top end of the cell

    * Negative (โˆ’) terminal: flat bottom end of the cell

* Blue outer wrap: insulating sleeve carrying the rating


Getting started: charging and first use

  1. Check the cell for dents, torn wrap or swelling. Do not use a damaged cell.
  2. Use a charger made for single-cell Li-ion (4.2 V full charge).  A TP4056-style module with protection or a good 18650 charger both work.
  3. Insert the cell with the polarity correct (+ to +, โˆ’ to โˆ’). Reversing it can damage the cell and the charger.
  4. Charge on a non-flammable surface and stay nearby, especially for the first few charges.
  5. Unplug the charger once the cell is full. A fully charged Li-ion cell reads about 4.2 V on a multimeter.
  6. Fit the cell into a proper 18650 holder or battery shield, then connect your device.

 Good to know

  • Never short the terminals. A short can cause heat, fire or venting.
  • Do not over-discharge. Stop using the cell when it drops to about 3.0V. Going lower shortens its life.
  • Keep away from heat and water. Do not leave it in a hot car or in direct sun.
  • Series and parallel packs: use cells of the same brand, capacity and charge level, and add a BMS.
  • High-current loads: the maximum discharge current is not stated, so keep heavy loads (motors, high-power LEDs) modest or use a cell with a published rating.
  • Storage: for long storage, keep it partly charged (around 3.7 V), in a cool dry place.
  • Keep away from children.

 Applications

  • Airsoft electric guns (AEGs) and accessories
  • Torches and diving lights
  • DIY power banks and portable chargers
  • ESP32 / Arduino battery-powered projects (with a boost converter or regulator)
  • Portable speakers, small fans and handheld devices
  • Replacement cell for 18650 battery packs

You might also like

5mm LED Green Color

5mm LED Green Color

In Stock

RWF 100

4 Channel 5V Relay Module

4 Channel 5V Relay Module

In Stock

RWF 7,000 RWF 6,000

Nodemcu ESP8266 WiFi Development Board

Nodemcu ESP8266 WiFi Development Board

In Stock

RWF 11,000

Resistive soil moisture sensor

Resistive soil moisture sensor

Low Stock

RWF 4,500